## Tuesday, January 26, 2010

### How To Put Your iPhone Into Field Test Mode & Compare Signal Strength Bars To Actual Signal Levels

In a previous post I showed how to do Decibel (dB) calculations when both the input power and output power are known for a transmission system. We learned that a 50% decrease between input and output power results in a power loss of -3 dB with the negative sign indicating the loss in power.

These calculations work great if you know both the input and output power but - what if you don't know the input power? And, because dB calculations are made based on an output power to input power ratio, they really don't tell you much when it comes to things like actual signal strength. What's the solution? Something called a dBm calculation. dBm calculations are done in basically the same way we do dB calculations, the only real difference being we replace the input power value in the equation with a 1 mW constant:

Psignal in dBm = 10 x log10(Psignal in Watts/1mW)

Where Psignal in Watts is the signal strength measured in Watts. This equation can be simplified using some basic math since 1mW is now a constant, yielding:

Psignal in dBm = 10 x (log10Psignal in Watts) + 30

Pretty simple, the dBm level of a signal that has been measure in Watts is just ten times the base-10 log of the measured signal plus 30. It's actually so simple it's much more common to measure and indicate communications signals in dBm. In fact, you can take some measurements yourself if you happen to own an iPhone. Let's learn how.

The iPhone has the ability to go into something called Field Test mode. Once in this mode you can look at signal strength in both signal bars (what we are all used to seeing) and also in dBm. To put an iPhone into Field Test mode just punch in the following number on the phone keypad, including the "star" and "pound sign" keys:

*3001#12345#*

After you punch these numbers and symbols in, hit the Call button on the keypad and you'll end up with your iPhone screen looking like this:

Lots of interesting stuff here but - for now - let's ignore everything but the upper left hand corner of the screen. Take a look at where you usually see the signal bars and you'll see a negative number - this is the actual cell signal strength your phone is receiving in dBm referenced to 1 mW. In the above screen shot I'm measuring -113 dBm. Touch that signal strength number once and it toggles to the familiar signal strength bars:

Touch it again and it flips back to the strength number. You get the idea. What constitutes a good signal? Here's some rough signal strength guidelines:

Full Signal:-70 or lower
Optimal Signal:-70 to -75
Fair Signal:-75 to -85

Poor Signal: -85 or higher

Remember as a negative number increases in its numeric value it is actually decreasing with reference to zero. This means a -70 dBm signal is stronger than a -85 dBm signal.

This is interesting to experiment with - check your signal strength in different locations see and how it correlates to the numbers of bars you are getting. Does it match up? Not always based on my experience!

To exit out of Field Test mode on the iPhone just hit the Home button.

Have a Blackberry? (I don't so proceed with this one at your own risk) I've been told you can do something similar using the secret code Alt-NMLL to convert your bars to numbers. To convert back to signal strength bars just enter the same secret code again.

Have a phone other than an iPhone or Blackberry? Most phones will allow you to go into some sort of field mode to see actually signal strength numbers. Check your manual or do some searching on the web to find out how.

7/6/10 Update: This function appears to be disabled after completing the iOS 4 Software Update

dav3m0r6an said...

This didn't work for my phone! I have the iPhone 3G, not the S. I have been to be able to access this field test mode with
*3001#12345#*, I use it in evaluating sites for building a BDA system for my clients who suffer from poor signal reception.

Gordon F Snyder Jr said...

Thank you - you got it - I had a typo in my post!!!!

Anonymous said...

I still works on iOS 9.1 and on Windows Phone you have to dial ##3282